How to Cut Jeans to Make a Wider Leg (with Pictures) (2024)

1. 1

   Determine how wide you want the bell to be and how far up the leg you want it to begin. To work well, the opening should not extend any further up than 1 inch below the knee.

2. 2

   Choose your insert material.

   • Try to keep your insert fabric close to the weight of the pants fabric. Denim with denim, twill with twill, etc.
   • Choose a patterned fabric, an alternating color, or paint or embroider on your insert for contrast. You might also match the color and weight closely for a more a subtle version.

3. 3

   Start at the bottom of the leg on each side, using a seam ripper to open the seam to your desired length. You will sew the top of these slits closed (so that it doesn't tear anymore) later, when you add the insert (known as a 'gusset').

4. 4

   Use the seam ripper to open the hem of the leg several inches on each side of the slit. You will sew this back into place later when you hem the edge of the gusset.

5. 5

   Measure your openings.

6. 6

   Transfer measurement to gusset material.

7. 7

   Fold two pieces of your gusset material in half, one over the other, and mark your cutting line diagonally on the wrong side of the fabric.

   • Be certain the diagonal cut is slightly longer than your slit length.
   • When measuring where the bottom cut should begin, keep in mind that you are cutting twice the width that you are looking at because of the fold in your material (e.g. 4.5 inches will open to 9 inches).
   • The reason for doing two pieces at once is to ensure that your gussets match in size and shape.

8. 8

   Cut both sides of your triangle gusset at the same time, keeping them symmetrical.

9. 9

   Turn the pants inside out.

   See Also

   6 Incredible Historic Hotels In Texas Big Bend CountryHermosa blusa tejida a crochet con explicación y patronesHow to Knit, Purl and Bind Off Stitches in Continental Knitting – Step by StepCelebrity Couples That Have Surprisingly Large Age Gaps

10. 10

    Pin the gusset edges to the raw edges of the slit legs, with right sides together.

11. 11

    Stitch down the edges of your pinned gusset. It is best if you use the same amount of seam allowance as was used to create the pants.

12. 12

    Press your seams away from the gusset.

13. 13

    Turn the pants right side out and top stitch the seams. This will reinforce both your long seam as well as the top of the slit opening. You may want to backstitch several times over the top point of the slit to prevent unraveling later.

    • As you top stitch, you will need to hold the area being sewn flat while allowing the pant leg to bunch up around the presser foot.

14. 14

    Roll the hems together and re-stitch the hem line.

15. 15

    Turn the pants right side out and repeat the process for the other leg.

16. 16

    Trim any loose threads. Wear them proudly!

Community Q&A

• Practice on an old pair of pants first.

• Whenever possible, unravel the seam rather than cutting the material, then sew the open seams flat on each side of the leg opening. Unraveling the seam will make it much easier to sew the insert in.

• You can also reshape jeans right out of the washer and air dry i.e straighten them out, then stretch the bottoms to desired shape. Pulling legs straight down hard will lengthen them a bit too just be sure to reshape the bottom and air dry. The stiffness will go away after a short while wearing.

• You may end up ruining your pants. If so, just make them into shorts!

• Scissors
• Thread to match the weight and color of the heaviest fabric
• Needle or sewing machine
• Fabric for gusset
• Iron
• Straight pins

You Might Also Like

Co-authors: 27

Updated: March 24, 2024

Views:462,146

Article Rating:96% - 123 votes

Categories: Featured Articles | Jeans

Spanish

Portuguese

Russian

Italian

Indonesian

German